Language

News

Make the gardens more beautiful & make the world brighter!

5w solar wall light introduction

time:2020-11-22 source:ZJ Lighting Views:106


Schematic diagram of a new type of lamp body structure split; Figure 1-2 is a diagram of a new type of chassis base structure split; Figure 2 is a schematic diagram of the appearance of the lamp after installation. Battery base 1, lamp cover 2, middle cover 3, reflector 4, seal ring 5, stop plug 6, wall seat lining 7, expansion screw 9, upper cap 11, lamp cover fixing sleeve 12, lamp housing screw 13, base plate 14 , Support tube one 15, support tube two 16, stuffing cap 17, saddle pad 18, chassis 19, lining 20, long screw 21, short screw 22, hexagon nut 24, screw 25, hexagon screw 26, cap nut 27, from Tapping screw 28, screw 31, cap nut 32, solar panel 33, circuit board 34, rechargeable battery 35, LED36.

Detailed ways

Hereinafter, the new technical solution will be further explained in detail through the embodiments and the accompanying drawings. For example, the solar wall light shown in Fig. 1 and Fig. 2 is used. The solar panel 33 is the energy source of the 5w solar wall light. The electric power is supplied to the rechargeable battery 35 by connecting the power cord. The solar panel 33 is placed under the upper cap 11. After the LED36, rechargeable battery 35, circuit board 34, and toggle switch are installed in the battery base 1, put the sealing ring 5 into the upper edge of the battery base 1; the reflector 4 is fixed on the middle cover 3 with screws 31; the middle cover 3 is screwed Into the slot of the battery base 1. The two ends of the lamp housing screw 13 are covered with upper limit plugs 6, which penetrate the four stainless steel tubes on the lamp housing fixing sleeve 12. The lampshade 2 is inserted into the battery base 1 and placed on the solar panel 33, the lampshade fixing sleeve 12 is put on the lampshade 2, the screw on one end of the lampshade fixing sleeve 12 passes through the hole on the upper cap 11 and is fixed with a cap nut 32, and the screw on the other end passes through The holes on the bottom plate 14 are fixed with cap nuts. The short screw 22 is screwed into the threaded hole on the inner lining 20 and then put into the support tube 15 with the screw head outward; the long screw 21 penetrates into the hole of the support tube 15 and screwed into the threaded hole of the inner lining 20; Sleeve the other end of the support tube 15 and fix it with the inner lining 20 of the screw 25; put the saddle pad 18 and the support tube 16 in turn on the long screw 21 fixed on the inner lining 20, the hole of the chassis 19 Put it on the long screw and tighten it with a nut, so that the entire hanging foot has been formed; finally the bottom plate 14 and the hanging foot are fixed, and the short screw 22 is screwed through the hole of the bottom plate 14 with the nut 24. The hexagonal screw 26 is installed in the wall seat lining 7, and then the wall seat lining 7 is screwed on the expansion screw 9 previously installed on the wall with a self-tapping screw 28. After the chassis 19 is inserted into the wall seat lining 7, use a cap nut 27 Screw the hexagonal screw 26 to fix the whole lamp.

A solar wall light according to claim, characterized in that it has a lamp body and a chassis base installed perpendicularly to the lamp body; the lamp body includes a power supply system and a cover installed between the bottom plate and the upper cap; the power supply system includes The solar panel (33) under the upper cap (11), the LED (36), the rechargeable battery (35), and the circuit board (34) that are electrically connected to the solar panel and installed in the battery base (01); the cover set Outside the power system, it includes a lampshade (02) and a lampshade fixing sleeve (12) sleeved on the outside of the lampshade; the chassis base includes a support pipe (15) connected to the bottom plate, and a support pipe two ( 16), the chassis (19) connected with the second support tube.